Kirjoittaja Aihe: usb-kovo ongelma  (Luettu 6462 kertaa)

0 jäsentä ja 1 Vieras katselee tätä aihetta.

wode

  • Vieras
usb-kovo ongelma
« : 10.12.2006 - klo:12:54 »
Olis pienoinen onkelma tässä 10.2 susessa kun ei ulkoinen usb-kovo
suostu toimimaan.Kun laitan usb liittimen paikalleen niin se kovo rupeaa
"pumppaamaan" eli yrittää liittä sitä mutta eipä onnistu homma.

Mulla on samassa koneessa toisella osiolla fedora6 ja siellä homma pelittää
ihan ok eli kovossa ei ole vikaa.

Kaikki muut usb laitteet toimii ihan ok.

Oliskos jollakin jotain ideaa mistä homma kiikastaa??

Poissa jmp

  • openSUSE Member
  • *
  • Viestejä: 4553
  • Sukupuoli: Mies
    • openSUSEa suomeksi
Vs: usb-kovo ongelma
« Vastaus #1 : 10.12.2006 - klo:13:01 »
mitä sanoo dmesg kun liität laitteen järjestelmään?
Ja muistakaa pitää hauskaa ;)

openSUSE Tumbleweed (x86_64)

juippis

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #2 : 10.12.2006 - klo:13:16 »
Ja sitten "lsusb"

wode

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #3 : 10.12.2006 - klo:13:56 »
Tässä ensiksi dmesg ja lopussa lsusb
Laitoin koodin kun oli niin iso liitetidostona mutta ei ilmeisesti
näy muille joten laitan tähän pätkän.
Koodia: [Valitse]
Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdf: 160836480 512-byte hdwr sectors (82348 MB)
usb 1-7: reset high speed USB device using ehci_hcd and address 29
usb 1-7: failed to restore interface 0 altsetting 0 (error=-110)
usb 1-7: USB disconnect, address 29
sdf: Write Protect is off
sdf: Mode Sense: 03 00 00 00
sdf: assuming drive cache: write through
sdf : READ CAPACITY failed.
sdf : status=0, message=00, host=1, driver=00
sdf : sense not available.
sdf: Write Protect is off
sdf: Mode Sense: 00 00 00 00
sdf: assuming drive cache: write through
sd 22:0:0:0: Attached scsi disk sdf
sd 22:0:0:0: Attached scsi generic sg6 type 0
usb-storage: device scan complete
usb 1-7: new high speed USB device using ehci_hcd and address 30
usb 1-7: device descriptor read/64, error -71
usb 1-7: device descriptor read/64, error -71
usb 1-7: new high speed USB device using ehci_hcd and address 31
usb 1-7: new device found, idVendor=07ab, idProduct=fccd
usb 1-7: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-7: Product: FHD-Classic
usb 1-7: Manufacturer: Freecom Technologies
usb 1-7: SerialNumber: 100000000000000013424
usb 1-7: configuration #1 chosen from 1 choice
scsi23 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 31
usb-storage: waiting for device to settle before scanning
  Vendor: HDS72808  Model: 0PLAT20           Rev: PF2O
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdf: 160836480 512-byte hdwr sectors (82348 MB)
usb 1-7: reset high speed USB device using ehci_hcd and address 31
usb 1-7: failed to restore interface 0 altsetting 0 (error=-110)

freecom on se kovo
ja sitten
Koodia: [Valitse]
wode@linux-w2:~> lsusb
Bus 001 Device 004: ID 07ab:fccc Freecom Technologies
Bus 001 Device 001: ID 0000:0000 
Bus 002 Device 002: ID 04a9:2206 Canon, Inc. CanoScan N650U/N656U
Bus 002 Device 001: ID 0000:0000 
Bus 003 Device 003: ID 058f:9360 Alcor Micro Corp.
Bus 003 Device 002: ID 046d:c512 Logitech, Inc.
Bus 003 Device 001: ID 0000:0000 
wode@linux-w2:~>
Opinpahan pikkuhiljaa käyttämään näitä teidän hienoja jutskia ;D
« Viimeksi muokattu: 10.12.2006 - klo:18:46 kirjoittanut wode »

wode

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #4 : 10.12.2006 - klo:19:11 »
Saakos näistä mitään osviittaa ongelmasta???

Poissa jmp

  • openSUSE Member
  • *
  • Viestejä: 4553
  • Sukupuoli: Mies
    • openSUSEa suomeksi
Vs: usb-kovo ongelma
« Vastaus #5 : 10.12.2006 - klo:19:14 »
Kuinka tuo levy on osioitu?
Ja muistakaa pitää hauskaa ;)

openSUSE Tumbleweed (x86_64)

wode

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #6 : 10.12.2006 - klo:20:07 »
Se on 80gigan levy ja vain yksi osio.

Poissa jmp

  • openSUSE Member
  • *
  • Viestejä: 4553
  • Sukupuoli: Mies
    • openSUSEa suomeksi
Vs: usb-kovo ongelma
« Vastaus #7 : 10.12.2006 - klo:20:15 »
Se on 80gigan levy ja vain yksi osio.

Tuota riviä vain ihmettelin
sdf : READ CAPACITY failed.

Itselläni on ulkoinen firewire/usb-levy joka aina silloin tällöin antaa firewirenä käytettäessä virhettä

Dec 10 13:18:54 ambrym kernel: sdd: Current: sense key: Medium Error
Dec 10 13:18:54 ambrym kernel:     Additional sense: Logical unit communication CRC error (Ultra-DMA/32)
Dec 10 13:18:54 ambrym kernel: end_request: I/O error, dev sdd, sector 159
Dec 10 13:18:54 ambrym kernel: I/O error in filesystem ("sdd1") meta-data dev sdd1 block 0x60       ("xfs_trans_read_buf") error 5 buf count 4096


Tuohon auttaa vain kun vaihtaa USB:hen.

Voisitko kokeilla vaihtaa usb-porttia. Pysyykö virhe dmesgissä samana?
Ja muistakaa pitää hauskaa ;)

openSUSE Tumbleweed (x86_64)

wode

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #8 : 10.12.2006 - klo:20:48 »
Kokeilin toisessa portissa ja sama tulos
tässä tuloste
Koodia: [Valitse]
usb-storage: waiting for device to settle before scanning
  Vendor: HDS72808  Model: 0PLAT20           Rev: PF2O
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdf: 160836480 512-byte hdwr sectors (82348 MB)
usb 1-7: reset high speed USB device using ehci_hcd and address 45
usb 1-7: failed to restore interface 0 altsetting 0 (error=-110)
usb 1-7: USB disconnect, address 45
sdf: Write Protect is off
sdf: Mode Sense: 03 00 00 00
sdf: assuming drive cache: write through
sdf : READ CAPACITY failed.
sdf : status=0, message=00, host=1, driver=00
sdf : sense not available.
sdf: Write Protect is off
sdf: Mode Sense: 00 00 00 00
sdf: assuming drive cache: write through
sd 31:0:0:0: Attached scsi disk sdf
sd 31:0:0:0: Attached scsi generic sg6 type 0
usb-storage: device scan complete
usb 1-7: new high speed USB device using ehci_hcd and address 46
usb 1-7: device descriptor read/64, error -71
usb 1-7: device descriptor read/64, error -71
usb 1-7: new high speed USB device using ehci_hcd and address 47
usb 1-7: new device found, idVendor=07ab, idProduct=fccd
usb 1-7: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-7: Product: FHD-Classic
usb 1-7: Manufacturer: Freecom Technologies
usb 1-7: SerialNumber: 100000000000000013424
usb 1-7: configuration #1 chosen from 1 choice
scsi32 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 47
usb-storage: waiting for device to settle before scanning

juippis

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #9 : 11.12.2006 - klo:07:07 »
Hmm, laita se kiinni ja pastea komennot
cat /proc/partitions
cat /etc/mtab

voi olla, että hal on rikki ja tuo ei mounttaudu automaattisesti.

wode

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #10 : 11.12.2006 - klo:12:37 »
Kokeilin tuota hal-device-manageria fedorassa ja susessa kun laittaa kovon kiinni
ja tämmöiset oli tulokset.
fedora 6 hal 0.5.8.1 dbus 1.0.1
Koodia: [Valitse]
[wode@localhost ~]$ hal-device-manager

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_usbraw

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host_scsi_device_lun0

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host_scsi_device_lun0
Introspect error: No device with id /org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240
Exception dbus_bindings.DBusException: 'No device with id /org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240' in 'dbus_bindings._GIL_safe_cmessage_function_handler' ignored

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_usbraw

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_usbraw

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host_scsi_device_lun0

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_1000000000000000134240_if0_scsi_host_scsi_device_lun0_scsi_generic

DeviceAdded, udi=/org/freedesktop/Hal/devices/storage_serial_HDS72808_0PLAT20_1000000000000000134240

DeviceAdded, udi=/org/freedesktop/Hal/devices/volume_part2_size_1024

DeviceAdded, udi=/org/freedesktop/Hal/devices/volume_uuid_4331_DDA7

PropertyModified, device=/org/freedesktop/Hal/devices/volume_uuid_4331_DDA7
  key=volume.mount_point, rem=0, add=0
  value=/media/disk
  key=volume.is_mounted, rem=0, add=0
  value=True
 
ja suse hal 0.5.8 dbus 1.0.0
Koodia: [Valitse]
wode@linux-w2:~> hal-device-manager
GTK Accessibility Module initialized
Bonobo accessibility support initialized

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0_scsi_host

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_usbraw

DeviceAdded, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0_scsi_host_scsi_device_lun0

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0_scsi_host_scsi_device_lun0
Older versions of the D-BUS bindings have an error when removing signals. Please upgrade.
Trying to remove unkown rule: type='signal',interface='org.freedesktop.Hal.Device',sender=':1.3',path='/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0_scsi_host_scsi_device_lun0',member='PropertyModified'
Introspect error: No device with id /org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424
Exception dbus_bindings.DBusException: 'No device with id /org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424' in 'dbus_bindings._GIL_safe_cmessage_function_handler' ignored

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0_scsi_host
Older versions of the D-BUS bindings have an error when removing signals. Please upgrade.
Trying to remove unkown rule: type='signal',interface='org.freedesktop.Hal.Device',sender=':1.3',path='/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0_scsi_host',member='PropertyModified'

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_usbraw
Older versions of the D-BUS bindings have an error when removing signals. Please upgrade.
Trying to remove unkown rule: type='signal',interface='org.freedesktop.Hal.Device',sender=':1.3',path='/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_usbraw',member='PropertyModified'

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0
Older versions of the D-BUS bindings have an error when removing signals. Please upgrade.
Trying to remove unkown rule: type='signal',interface='org.freedesktop.Hal.Device',sender=':1.3',path='/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424_if0',member='PropertyModified'

DeviceRemoved, udi=/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424
Older versions of the D-BUS bindings have an error when removing signals. Please upgrade.
Trying to remove unkown rule: type='signal',interface='org.freedesktop.Hal.Device',sender=':1.3',path='/org/freedesktop/Hal/devices/usb_device_7ab_fccd_100000000000000013424',member='PropertyModified'
Eli dbus:in käskee päivittämään mutta viimeisin paketti on asennettu.Onko tämä bugi vai ootellaanko päivityksiä??

wode

  • Vieras
Vs: usb-kovo ongelma
« Vastaus #11 : 11.12.2006 - klo:13:00 »
Juippis
Lainaus
Hmm, laita se kiinni ja pastea komennot
cat /proc/partitions
cat /etc/mtab

Näissä näkyy vain normaalit kovon osiot ei mitään ylimääräistä.