openSUSEa suomeksi
openSUSE => Asennus ja käyttö => Aiheen aloitti: RaijaR - 25.11.2008 - klo:19:10
-
Ostin ulkoisen 400 Gb:n USB-levyaseman (Fujitsu-Siemens storagebird 35ev821). Gzippasin oman kotihakemiston ja yritin siirtää sen em. levyasemalle, mutta ei onnistunut.
Ohessa jotain (toivottavasti) valaisevaa:
cp rruuska_251108.tar.gz /media/32_00_00/
cp: writing `/media/32_00_00/rruuska_251108.tar.gz': File too large
Bus 002 Device 017: ID 152d:2329 JMicron Technology Corp. / JMicron USA Technology Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x152d JMicron Technology Corp. / JMicron USA Technology Corp.
idProduct 0x2329
bcdDevice 0.00
iManufacturer 10
iProduct 11
iSerial 3
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 6
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)
-
Pari kysymystä:
Mikä tuon levyaseman tiedostojärjestelmä on?
Kuinka suuri tuo rruuska_251108.tar.gz-tiedosto on?
-
En tiedä, mikä tuon tiedostojärjestelmä on (epäilen suuresti, että "Windows Vista"). Kuinka sen katson konsolilla?
Tarripallon koko on 7.1 GB.
-
Kuinka sen katson konsolilla?
#fdisk -l näyttää onko se Fat.
-
fdisk -l
Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x000cc05f
Device Boot Start End Blocks Id System
/dev/sda1 1 9 72261 83 Linux
/dev/sda2 19083 19457 3012187+ 5 Extended
/dev/sda3 * 10 2620 20972857+ 83 Linux
/dev/sda4 2621 19082 132231015 83 Linux
/dev/sda5 19083 19457 3012156 82 Linux swap / Solaris
Partition table entries are not in disk order
Disk /dev/sdf: 400.0 GB, 400088457216 bytes
255 heads, 63 sectors/track, 48641 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x71f31e23
Device Boot Start End Blocks Id System
/dev/sdf1 * 1 48641 390708801 c W95 FAT32 (LBA)
======================================
Höö, mikäs tommonen FAT32 on?!
-
Höö, mikäs tommonen FAT32 on?!
Juu se on Windowsissa käytetty tiedostojärjestelmä, jolla suurin tiedostokoko on 4GB.
Joko kopioit pienempiä tiedostoja, kuin 4GB, tai muutat USB-levyn tiedostojärjestelmäksi joko Windowsin tunteman NTFS, tai sitten jonkun linuxin käyttämän esim ext2 tai ext3, joissa ei ole tuota kokorajoitusta.
-
Kuinka initialisoin tuon ulkoisen winsun linux formaattiin?
-
Kuinka initialisoin tuon ulkoisen winsun linux formaattiin?
Yastilla. Järjestelmä/Osiointityökalu. Se on sitten /dev/sdf.
-
Entäs sitten?
-
Pidä tuo sdf1 valittuna ja paina Delete ja sitten Create ja valitse asemaksi tuo sdf sitten valitset filesystem joko xfs tai ext3 ja format
-
Tein suoraan modify-komennolla, kun en saanut mitään aikaiseksi delete-create -komentoparilla.
Valitsin EXT3:sen, formatointi alkoi ja melkein meni läpi. Valitti, ettei saa asetettua mount pointtia fstabbiin, joten vaihdoin nimeksi sdf1:sen. Tuo meni sitten ok läpi. Kopiointi ei sitten onnistunutkaan, koska sdf1:llä oli vain rootin oikeudet. Muutin ne, ja nyt on sdf1:lle saatu kopioitua tarripallo, joka on samankokoinen kuin alkuperäinen (lienee ok?). Tarttee vielä testata, mutta ei enää tänään.