openSUSEa suomeksi
openSUSE => Turvallisuus ja laitteisto => Aiheen aloitti: usbkauno - 06.10.2009 - klo:22:57
-
Hei! Asensin openSUSE 11.1, Compaq EVO N610c kannettavaan. Asennuksen hoidin netinstall versiona ja johdon päässä.
Kun asennus oli valmis ja käynnistelin susea huomasin ettei W200 Wireless lan adapterin valo palanut eikä korttia löytynyt mistään asetuksista... Netti kyllä toimi kaapelilla joten löysin ohjeet korttia varten lucidtips.com:ista mutta ne eivät ilmeisesti täsmänneet tai en vain ymmärtänyt kaikkea.
Olen aloittelija linuxien kanssa ja toivon että saan tarpeeksi selkeitä ohjeilta niiltä jotka ymmärtävät miten saa kyseisen adapterin käyttöön... Kyseessä ei siis ole mikään USB tai PCMIA kortti vaan multiportissa koneen kannessa oleva palikka :)
ps. Vaikuttaako kun tietoja laitteistosta ilmoittaa muutamien osien olevan peräisin eri mallisesta EVO:sta (N600c)
//Daniel Halonen
-
Avaa komentoikkuna ja aja seuraava komento ja laita printti tänne.
/sbin/lspci -v
-
00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host Bridge (rev 04)
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, fast devsel, latency 0
Memory at 60000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, 66MHz, fast devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 40300000-403fffff
Prefetchable memory behind bridge: 48000000-4fffffff
Kernel modules: shpchp
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=07, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 40000000-402fffff
Prefetchable memory behind bridge: 50000000-57ffffff
Kernel modules: shpchp
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
Flags: bus master, medium devsel, latency 0
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at 4440 [size=16]
Memory at 58000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
Kernel modules: piix, ata_piix
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97 Audio Controller (rev 02)
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 4000 [size=256]
I/O ports at 4400 [size=64]
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] (prog-if 00 [VGA controller])
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, stepping, 66MHz, medium devsel, latency 66, IRQ 11
Memory at 48000000 (32-bit, prefetchable) [size=128M]
I/O ports at 3000 [size=256]
Memory at 40300000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 40320000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: radeonfb
02:06.0 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 40000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=03, sec-latency=176
Memory window 0: 50000000-53fff000 (prefetchable)
Memory window 1: 5c000000-5ffff000
I/O window 0: 00002400-000024ff
I/O window 1: 00002800-000028ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:06.1 CardBus bridge: Texas Instruments PCI1420 PC card Cardbus Controller
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 40080000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 54000000-57fff000 (prefetchable)
Memory window 1: 70000000-73fff000
I/O window 0: 00002c00-00002cff
I/O window 1: 00001400-000014ff
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:08.0 Ethernet controller: Intel Corporation 82801CAM (ICH3) PRO/100 VM (KM) EthernetController (rev 42)
Subsystem: Compaq Computer Corporation Evo N600c
Flags: bus master, medium devsel, latency 66, IRQ 10
Memory at 40100000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 2000 [size=64]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: e100, eepro100
02:0e.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at 40180000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
02:0e.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at 40200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
02:0e.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: Compaq Computer Corporation Device 00b7
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at 40280000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
EDIT: http://h20331.www2.hp.com/hpsub/cache/311483-0-0-225-121.html
tietoa wlan kortista, Siellä lukee myös et kyseessää usb... vaikka kortti multiport paikalla onkin.
-
laita vielä
/usr/bin/lsusb -v
-
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0002 2.0 root hub
bcdDevice 2.06
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0004 1x 4 bytes
bInterval 12
can't get hub descriptor: Operation not permitted
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
can't get hub descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 64
idVendor 0x1d6b Linux Foundation
idProduct 0x0001 1.1 root hub
bcdDevice 2.06
iManufacturer 3
iProduct 2
iSerial 1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
can't get hub descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)
Ja halluat varmaan lsmod myös? ;)
-
No ei noista paljon irronnut. Missä kohtaa se tökkäsi tossa kun seurasit noita asennusohjeita vai menikö kaikki ohjeen mukaan läpi?
-
http://www.lucidtips.com/2008/09/06/wireless-using-w200-on-opensuse-110/
tökkää aina siinä kohtaa ku krijotetaan pelkkä make ; linux-lf0h:/lib/modules/2.6.27.29-0.1-pae/build # cd usb
linux-lf0h:/lib/modules/2.6.27.29-0.1-pae/build/usb # make
make -C /usr/src/linux-2.6.27.29-0.1-obj/i386/pae M=/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb KERNELRELEASE=2.6.27.29-0.1-pae modules
make[1]: Siirrytään hakemistoon "/usr/src/linux-2.6.27.29-0.1-obj/i386/pae"
make -C /usr/src/linux-2.6.27.29-0.1 O=/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/. modules
CC [M] /usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.o
In file included from /usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:90:
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.h: In function ‘orinoco_spin_unlock’:
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.h:188: warning: ‘__raw_spin_unlock’ is static but used in inline function ‘orinoco_spin_unlock’ which is not static
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.h:188: warning: ‘raw_local_irq_enable’ is static but used in inline function ‘orinoco_spin_unlock’ which is not static
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c: In function ‘orinoco_translate_scan’:
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3975: warning: passing argument 1 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3975: warning: passing argument 3 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3975: warning: passing argument 4 of ‘iwe_stream_add_event’ makes pointer from integer without a cast
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3975: error: too few arguments to function ‘iwe_stream_add_event’
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3985: warning: passing argument 1 of ‘iwe_stream_add_point’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3985: warning: passing argument 3 of ‘iwe_stream_add_point’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3985: warning: passing argument 4 of ‘iwe_stream_add_point’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3985: error: too few arguments to function ‘iwe_stream_add_point’
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3995: warning: passing argument 1 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3995: warning: passing argument 3 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3995: warning: passing argument 4 of ‘iwe_stream_add_event’ makes pointer from integer without a cast
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:3995: error: too few arguments to function ‘iwe_stream_add_event’
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4005: warning: passing argument 1 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4005: warning: passing argument 3 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4005: warning: passing argument 4 of ‘iwe_stream_add_event’ makes pointer from integer without a cast
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4005: error: too few arguments to function ‘iwe_stream_add_event’
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4019: warning: passing argument 1 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4019: warning: passing argument 3 of ‘iwe_stream_add_event’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4019: warning: passing argument 4 of ‘iwe_stream_add_event’ makes pointer from integer without a cast
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4019: error: too few arguments to function ‘iwe_stream_add_event’
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4028: warning: passing argument 1 of ‘iwe_stream_add_point’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4028: warning: passing argument 3 of ‘iwe_stream_add_point’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4028: warning: passing argument 4 of ‘iwe_stream_add_point’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4028: error: too few arguments to function ‘iwe_stream_add_point’
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4053: warning: passing argument 1 of ‘iwe_stream_add_value’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4053: warning: passing argument 4 of ‘iwe_stream_add_value’ from incompatible pointer type
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4053: warning: passing argument 5 of ‘iwe_stream_add_value’ makes pointer from integer without a cast
/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.c:4053: error: too few arguments to function ‘iwe_stream_add_value’
make[4]: *** [/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb/orinoco.o] Virhe 1
make[3]: *** [_module_/usr/src/linux-2.6.27.29-0.1-obj/i386/pae/usb] Virhe 2
make[2]: *** [sub-make] Virhe 2
make[1]: *** [all] Virhe 2
make[1]: Poistutaan hakemistosta "/usr/src/linux-2.6.27.29-0.1-obj/i386/pae"
make: *** [modules] Virhe 2
-
Joo ei tuo kääntäminen onnistunut minullakaan. Ehkäpä toi ei ole enää yhteen sopiva 11.1 kanssa.