openSUSEa suomeksi
openSUSE => Asennus ja käyttö => Aiheen aloitti: guest766 - 27.08.2008 - klo:16:12
-
Latasin netistä näytönohjaimen päivitystiedoston ati-driver-installer-8-8-x86.x86_64.run
Mitenhän tuo asennetaan ja kannattaako moinen? Ettei men taas kaikki sekaisin.
-
sh ati-driver-installer-8-8-x86.x86_64.run. Roottina.
-
Toimii vapaalla ajurilla, 3D työpöydän takia tuota ei tarvitse asentaa.
-
Google Earth pätkii ja käskee asentaa.
-
No sitten se pitää varmaan asentaa. Paketit löytyvät myös ATIn asennuslähteestä.
-
Kyllä minulla se päällä on, mistä näen onko ne jo asennettu?
-
Oma tietokone, mitä siellä kerrotaan näytönhjaimen kohdalla?
Ja konsolissa tavan käyttäjänä: glxgears, jos tulee ruutu jossa pyörii kolme ratasta niin silloin pitäisi
toimia 3d-kiihdytys ja olla ajurit asennettuna kuten pitää.
-
Kyllä minulla se päällä on, mistä näen onko ne jo asennettu?
glxinfo |grep "OpenGL "
Tulosteen pitäisi olla jotain alla olevan kaltaista
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI <ohjaimen malli>
OpenGL version string: 2.x.x <versio numero>
-
Tämmönen tuli.
Noble@linux-1zgj:~> glxinfo |grep "OpenGL "
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.4 (2.1 Mesa 7.0.3)
OpenGL extensions:
Noble@linux-1zgj:~>
-
No tuon mukaan ATIn ajuri ei ole käytössä (tai ainakaan sen 3D kiihdytys ei ole käytössä).
Mikä ajuri on xorg.conf-tiedoston mukaan käytössä?
-
Mitenkäs tuo katsotaan?
-
Hei nyt tuli tällanen kun buuttasin koneen.
Noble@linux-1zgj:~> glxinfo |grep "OpenGL "
OpenGL vendor string: DRI R300 Project
OpenGL renderer string: Mesa DRI R300 20060815 AGP 1x x86/MMX/SSE2 TCL
OpenGL version string: 1.3 Mesa 7.0.3
OpenGL extensions:
Noble@linux-1zgj:~>
-
Komenna
cat /etc/X11/xorg.conf
sitten etsit sieltä kohdan jossa on jotain alla olevan kaltaista
Section "Device"
BoardName "Radeon"
BusID "1:0:0"
Driver "fglrx" # tämä voi olla myös radeon
Identifier "Device[0]"
VendorName "ATI"
EndSection
OpenGL vendor string: DRI R300 Project
OpenGL renderer string: Mesa DRI R300 20060815 AGP 1x x86/MMX/SSE2 TCL
OpenGL version string: 1.3 Mesa 7.0.3
OpenGL extensions:
Noble@linux-1zgj:~>
Ja se oli sitten radeon ;) Eli käytössä on tuo avoin ajuri.
Tuo radeon pitää muuttaa muotoon fglrx jos haluat käyttää ATIn ajuria. Tee varmuuskopio alkuperäisestä tiedostosta ennen muutoksen tekoa.
-
Nyt tuli kauhee määrä tavaraa.
Noble@linux-1zgj:~> cat /etc/X11/xorg.conf
# /.../
# SaX generated X11 config file
# Created on: 2008-08-04T08:33:14+0300.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax@suse.de>, 2005
# Contact: SaX-User list <https://lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#
Section "Files"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/URW"
FontPath "/usr/share/fonts/Speedo"
FontPath "/usr/share/fonts/PEX"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/latin2/misc:unscaled"
FontPath "/usr/share/fonts/latin2/75dpi:unscaled"
FontPath "/usr/share/fonts/latin2/100dpi:unscaled"
FontPath "/usr/share/fonts/latin2/Type1"
FontPath "/usr/share/fonts/latin7/75dpi:unscaled"
FontPath "/usr/share/fonts/baekmuk:unscaled"
FontPath "/usr/share/fonts/japanese:unscaled"
FontPath "/usr/share/fonts/kwintv"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/uni:unscaled"
FontPath "/usr/share/fonts/CID"
FontPath "/usr/share/fonts/ucs/misc:unscaled"
FontPath "/usr/share/fonts/ucs/75dpi:unscaled"
FontPath "/usr/share/fonts/ucs/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/misc:unscaled"
FontPath "/usr/share/fonts/hellas/75dpi:unscaled"
FontPath "/usr/share/fonts/hellas/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/Type1"
FontPath "/usr/share/fonts/misc/sgi:unscaled"
FontPath "/usr/share/fonts/xtest"
FontPath "/opt/kde3/share/fonts"
InputDevices "/dev/gpmdata"
InputDevices "/dev/input/mice"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "on"
Option "ZapWarning" "on"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "freetype"
Load "extmod"
Load "glx"
EndSection
Section "InputDevice"
Driver "kbd"
Identifier "Keyboard[0]"
Option "Protocol" "Standard"
Option "XkbLayout" "fi"
Option "XkbModel" "pc102"
Option "XkbRules" "xfree86"
EndSection
Section "InputDevice"
Driver "mouse"
Identifier "Mouse[1]"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Name" "ImPS/2 Generic Wheel Mouse"
Option "Protocol" "explorerps/2"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
DisplaySize 495 291
HorizSync 30-82
Identifier "Monitor[0]"
ModelName "VIEWSONIC VA2216W-2"
Option "DPMS"
Option "PreferredMode" "1680x1050"
VendorName "VSC"
VertRefresh 43-75
UseModes "Modes[0]"
EndSection
Section "Modes"
Identifier "Modes[0]"
Modeline "1680x1050" 144.55 1680 1784 1968 2256 1050 1051 1054 1086
Modeline "1680x1050" 115.00 1680 1728 1760 1840 1050 1053 1059 1079 +HSync -Vsync
Modeline "1280x1024" 138.54 1280 1368 1504 1728 1024 1025 1028 1069
Modeline "1280x1024" 128.94 1280 1368 1504 1728 1024 1025 1028 1066
Modeline "1280x1024" 119.40 1280 1368 1504 1728 1024 1025 1028 1063
Modeline "1280x1024" 113.00 1280 1328 1360 1440 1024 1027 1034 1061 +HSync -Vsync
Modeline "1280x1024" 108.88 1280 1360 1496 1712 1024 1025 1028 1060
Modeline "1280x960" 129.86 1280 1368 1504 1728 960 961 964 1002
Modeline "1280x960" 120.84 1280 1368 1504 1728 960 961 964 999
Modeline "1280x960" 110.95 1280 1360 1496 1712 960 961 964 997
Modeline "1280x960" 105.75 1280 1328 1360 1440 960 963 967 994 +HSync -Vsync
Modeline "1280x960" 102.10 1280 1360 1496 1712 960 961 964 994
Modeline "1024x768" 81.80 1024 1080 1192 1360 768 769 772 802
Modeline "1024x768" 76.16 1024 1080 1192 1360 768 769 772 800
Modeline "1024x768" 69.71 1024 1080 1184 1344 768 769 772 798
Modeline "1024x768" 69.50 1024 1072 1104 1184 768 771 775 796 +HSync -Vsync
Modeline "1024x768" 64.11 1024 1080 1184 1344 768 769 772 795
Modeline "800x600" 48.91 800 840 920 1040 600 601 604 627
Modeline "800x600" 45.50 800 840 920 1040 600 601 604 625
Modeline "800x600" 44.00 800 848 880 960 600 603 607 622 +HSync -Vsync
Modeline "800x600" 42.11 800 840 920 1040 600 601 604 623
Modeline "800x600" 38.22 800 832 912 1024 600 601 604 622
Modeline "1680x1050" 146 1680 1784 1960 2240 1050 1053 1059 1089 +hsync -vsync
EndSection
Section "Screen"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1680x1050" "1280x1024" "1280x960" "1024x768" "800x600"
EndSubSection
SubSection "Display"
Depth 16
Modes "1680x1050" "1280x1024" "1280x960" "1024x768" "800x600"
EndSubSection
SubSection "Display"
Depth 24
Modes "1680x1050" "1280x1024" "1280x960" "1024x768" "800x600"
EndSubSection
SubSection "Display"
Depth 8
Modes "1680x1050" "1280x1024" "1280x960" "1024x768" "800x600"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
Section "Device"
BoardName "RV350 AR"
#BusID "1:0:0"
Driver "radeon"
Identifier "Device[0]"
Option "GARTSize" "32"
VendorName "ATI"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
Section "Extensions"
EndSection
Noble@linux-1zgj:~>
-
Komenna root-käyttäjänä
cp /etc/X11/xorg.conf /etc/X11/xorg.conf_OMAKOPIO
Sitten muokkaat tuota tiedostoa vaikka vi-editorilla
Komenna
kwrite /etc/X11/xorg.conf
Etsi tiedostosta alla oleva kohta
Section "Device"
BoardName "RV350 AR"
#BusID "1:0:0"
Driver "radeon"
Identifier "Device[0]"
Option "GARTSize" "32"
VendorName "ATI"
EndSection
ja muokkaa tuota tiedostoa näin
Section "Device"
BoardName "RV350 AR"
#BusID "1:0:0"
Driver "fglrx"
Identifier "Device[0]"
# Option "GARTSize" "32"
VendorName "ATI"
EndSection
Tallenna muutoksesi ja käynnistä X (tai koko kone ) uudestaan.
-
Jos komennan kwrite /etc/X11/xorg.conf ei tapahdu mitään?
Kursori vaan jää paikalleen?
-
Asenna sitten vaikka nano komentamalla root-käyttäjänä
zypper in nano
se ainakin on helppo käyttää. Niin joo jos X ei enää tuon jälkeen toimi niin voit palauttaa vanhan xorg,conf tiedoston komentamalla
cp /etc/X11/xorg.conf_OMAKOPIO /etc/X11/xorg.conf
-
No niin, nyt onnistui. Vähän tuli pitkäsmäinen näyttö, mutta Google Earth
toimii. Näyttö on kyllä vähän suttusempi.
-
Mahtaako tämä olla vielä joku eri ajuri?
ati-driver-installer-8-8-x86.x86_64.run
-
Mahtaako tämä olla vielä joku eri ajuri?
ati-driver-installer-8-8-x86.x86_64.run
Samalta näyttäs tiedostonimi kuin ekassa postauksessa :)
Nyt en suoriltaan muista mutta itse jouduin aikanaan ajelemaan installeriskriptin jälkeen 'aticonfig --initial', joka muuttaa xorg.conf:in vastaamaan suoritettua ajuriasennusta (kaiketi näin :D).
Tämän jälkeen boottaus ja maailman pitäisi olla kaunis paikka..
(Lisäksi muistelen joskus olleen tarpeen komentaa: 'sax2 -r -m 0=fglrx', tai jotain tuohon suuntaan)
-
En saanut tuolla mitään aikaiseksi.
Näyttää siltä että ei ole oikea resoluutio minun monitorilleni.
1280*1024 70Hz on Catalyst Control Centerissä suurin.
Suurempi tars olla.
-
Jokapaikassa lukee 1680x1050? Miksi ei voi säätää kuin 1280x1050?
Section "Modes"
Identifier "Modes[0]"
ModeLine "1680x1050" 144.6 1680 1784 1968 2256 1050 1051 1054 1086
ModeLine "1680x1050" 115.0 1680 1728 1760 1840 1050 1053 1059 1079 +hsync -vsync
ModeLine "1280x1024" 138.5 1280 1368 1504 1728 1024 1025 1028 1069
ModeLine "1280x1024" 128.9 1280 1368 1504 1728 1024 1025 1028 1066
ModeLine "1280x1024" 119.4 1280 1368 1504 1728 1024 1025 1028 1063
ModeLine "1280x1024" 113.0 1280 1328 1360 1440 1024 1027 1034 1061 +hsync -vsync
ModeLine "1280x1024" 108.9 1280 1360 1496 1712 1024 1025 1028 1060
ModeLine "1280x960" 129.9 1280 1368 1504 1728 960 961 964 1002
ModeLine "1280x960" 120.8 1280 1368 1504 1728 960 961 964 999
ModeLine "1280x960" 111.0 1280 1360 1496 1712 960 961 964 997
ModeLine "1280x960" 105.8 1280 1328 1360 1440 960 963 967 994 +hsync -vsync
ModeLine "1280x960" 102.1 1280 1360 1496 1712 960 961 964 994
ModeLine "1024x768" 81.8 1024 1080 1192 1360 768 769 772 802
ModeLine "1024x768" 76.2 1024 1080 1192 1360 768 769 772 800
ModeLine "1024x768" 69.7 1024 1080 1184 1344 768 769 772 798
ModeLine "1024x768" 69.5 1024 1072 1104 1184 768 771 775 796 +hsync -vsync
ModeLine "1024x768" 64.1 1024 1080 1184 1344 768 769 772 795
ModeLine "800x600" 48.9 800 840 920 1040 600 601 604 627
ModeLine "800x600" 45.5 800 840 920 1040 600 601 604 625
ModeLine "800x600" 44.0 800 848 880 960 600 603 607 622 +hsync -vsync
ModeLine "800x600" 42.1 800 840 920 1040 600 601 604 623
ModeLine "800x600" 38.2 800 832 912 1024 600 601 604 622
ModeLine "1680x1050" 146.0 1680 1784 1960 2240 1050 1053 1059 1089 +hsync -vsync
EndSection
Section "Monitor"
Identifier "Monitor[0]"
VendorName "VSC"
ModelName "VIEWSONIC VA2216W-2"
UseModes "Modes[0]"
DisplaySize 495 291
HorizSync 30.0 - 82.0
VertRefresh 43.0 - 75.0
Option "DPMS"
Option "PreferredMode" "1680x1050"
EndSection
Section "Device"
#BusID "1:0:0"
Identifier "Device[0]"
Driver "fglrx"
VendorName "ATI"
BoardName "RV350 AR"
Option "GARTSize" "32"
BusID "PCI:1:0:0"
EndSection
-
Mitä sax2 näyttää resoluution kooksi.
-
1680x1050, mutta tää näyttö ei ole sitä vaan 1280x1024
Mistä suurennetaan?
-
1680x1050, mutta tää näyttö ei ole sitä vaan 1280x1024
Mistä suurennetaan?
Sieltä sax2 voit myös suurentaa sen.
-
Siellä on 1680x1050, mutta Catalyst Control Centerissä 1280x1024.
Ja tämän näytön resoluutio on nyt jälkimmäinen, eikä siitä siitä saa
suurennettua, vain pienennettyä. Ristiriitaiset arvot?
Ennen Atin ajurien asennusta oli tuo 1680x1050.
-
Kokeilitko käynnistää Sax2:n tällä: 'sax2 -r -m 0=fglrx'
Edit: Ja jos ei bootin jälkeen komento 'fglrxinfo' kerro jotain seuraavannäköistä:
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI RADEON 9600 Series
OpenGL version string: 2.1.7659 Release
Niin ajuri ei ole oikein asennettu/asentunut. Sitten voisit myös tarkistaa komentamalla:
'lsmod |grep fglrx'
että onko tuota ajuria edes ladattu kerneliin. Jotain tämänsuuntaista pitäisi tulla näkyviin:
fglrx 1737716 21
agpgart 38580 2 fglrx,via_agp
-
Kun kokeilin 'sax2 -r -m 0=fglrx' ja buuttasin niin resoluutioksi tuli 1400x1050.
Mutta vieläkään ei 1680x1050, mutta jo parempi.
Näin tuli.
Noble@linux-1zgj:~> fglrxinfo
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI RADEON 9600 Series
OpenGL version string: 2.1.7769 Release
Noble@linux-1zgj:~>
Ja näin.
Noble@linux-1zgj:~> lsmod |grep fglrx
fglrx 1780132 20
agpgart 50868 2 fglrx,intel_agp
Noble@linux-1zgj:~>
-
Kokeileppa sitten vielä syötellä noita näyttösi resoja ja mahdollisesti mutia "strategisia mittoja" aticonfig :illa, ks. 'aticonfig --help'.
Näyttäisi ainakin olevan mielenkiintoisin vaihtoehto tuo 'aticonfig --resolution=0,1680x1050'
Tuon jälkeen kun aticonfig on muuttanut sitten xorg.conf:ia, niin restartin (tai ulosloggaamisen ja sisäänloggaamisen jälkeen)
sitten mahdollisesti vielä joutuu käpistelemään Sax:ia, kuten edellä. Eli tarkistappa tämä vielä nykyisestä versiosta. :)
Edit: Tuolla aiemmin kun oli liittänyt postiisi xorg.conf:iä, jolloin käytössä oli radeon-ajuri, niin "Screen" -osiossa oli modes-kohdassa "1680x1050" sisältävä rivi. Edellisessä xorg.conf pätkässäsi olit vain laittanut Modeline-rivit, jotka eivät sikäli kerro että mitä screenille näytellään.
-
Ai tämä kokonaan?
Noble@linux-1zgj:~> cat /etc/X11/xorg.conf
# /.../
# SaX generated X11 config file
# Created on: 2008-08-29T15:53:39+0300.
#
# Version: 8.1
# Contact: Marcus Schaefer <sax@suse.de>, 2005
# Contact: SaX-User list <https://lists.berlios.de/mailman/listinfo/sax-users>
#
# Automatically generated by [ISaX] (8.1)
# PLEASE DO NOT EDIT THIS FILE!
#
Section "Files"
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/URW"
FontPath "/usr/share/fonts/Speedo"
FontPath "/usr/share/fonts/PEX"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/latin2/misc:unscaled"
FontPath "/usr/share/fonts/latin2/75dpi:unscaled"
FontPath "/usr/share/fonts/latin2/100dpi:unscaled"
FontPath "/usr/share/fonts/latin2/Type1"
FontPath "/usr/share/fonts/latin7/75dpi:unscaled"
FontPath "/usr/share/fonts/baekmuk:unscaled"
FontPath "/usr/share/fonts/japanese:unscaled"
FontPath "/usr/share/fonts/kwintv"
FontPath "/usr/share/fonts/truetype"
FontPath "/usr/share/fonts/uni:unscaled"
FontPath "/usr/share/fonts/CID"
FontPath "/usr/share/fonts/ucs/misc:unscaled"
FontPath "/usr/share/fonts/ucs/75dpi:unscaled"
FontPath "/usr/share/fonts/ucs/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/misc:unscaled"
FontPath "/usr/share/fonts/hellas/75dpi:unscaled"
FontPath "/usr/share/fonts/hellas/100dpi:unscaled"
FontPath "/usr/share/fonts/hellas/Type1"
FontPath "/usr/share/fonts/misc/sgi:unscaled"
FontPath "/usr/share/fonts/xtest"
FontPath "/opt/kde3/share/fonts"
InputDevices "/dev/gpmdata"
InputDevices "/dev/input/mice"
EndSection
Section "ServerFlags"
Option "AIGLX" "on"
Option "AllowMouseOpenFail" "on"
Option "IgnoreABI" "on"
Option "ZapWarning" "on"
EndSection
Section "Module"
Load "dbe"
Load "type1"
Load "freetype"
Load "extmod"
Load "glx"
Load "dri"
EndSection
Section "InputDevice"
Driver "kbd"
Identifier "Keyboard[0]"
Option "Protocol" "Standard"
Option "XkbLayout" "fi"
Option "XkbModel" "pc102"
Option "XkbRules" "xfree86"
EndSection
Section "InputDevice"
Driver "mouse"
Identifier "Mouse[1]"
Option "Buttons" "5"
Option "Device" "/dev/input/mice"
Option "Name" "ImPS/2 Generic Wheel Mouse"
Option "Protocol" "explorerps/2"
Option "Vendor" "Sysp"
Option "ZAxisMapping" "4 5"
EndSection
Section "Monitor"
Option "CalcAlgorithm" "XServerPool"
DisplaySize 495 291
HorizSync 30-82
Identifier "Monitor[0]"
ModelName "VIEWSONIC VA2216W-2"
Option "DPMS"
Option "PreferredMode" "1680x1050"
VendorName "VSC"
VertRefresh 43-75
UseModes "Modes[0]"
EndSection
Section "Modes"
Identifier "Modes[0]"
Modeline "1680x1050" 146.00 1680 1784 1960 2240 1050 1053 1059 1089 +HSync -VSync
Modeline "1400x1050" 121.75 1400 1488 1632 1864 1050 1053 1057 1089
EndSection
Section "Screen"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1680x1050" "1600x1024" "1600x1000" "1400x1050" "1280x1024" "1440x900" "1280x960" "1366x768" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1680x1050" "1600x1024" "1600x1000" "1400x1050" "1280x1024" "1440x900" "1280x960" "1366x768" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1680x1050" "1600x1024" "1600x1000" "1400x1050" "1280x1024" "1440x900" "1280x960" "1366x768" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1680x1050" "1600x1024" "1600x1000" "1400x1050" "1280x1024" "1440x900" "1280x960" "1366x768" "1280x800" "1152x864" "1280x768" "1280x720" "1024x768" "1280x600" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
Section "Device"
BoardName "ATI RADEON 9600 Series (RV350/RV360 4152)"
Driver "fglrx"
Identifier "Device[0]"
Option "XAANoOffscreenPixmaps" "true"
Option "Capabilities" "0x00000000"
Option "OpenGLOverlay" "off"
Option "FSAAScale" "0"
Option "FSAAEnable" "off"
Option "VideoOverlay" "on"
VendorName "ATI"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
Section "Extensions"
Option "Composite" "on"
EndSection
Noble@linux-1zgj:~>
-
Huomasin tämmösen.
Section "Modes"
Identifier "Modes[0]"
Modeline "1680x1050" 146.00 1680 1784 1960 2240 1050 1053 1059 1089 +HSync -VSync
Modeline "1400x1050" 121.75 1400 1488 1632 1864 1050 1053 1057 1089
EndSection
Mitä tuo +HSync -VSync tarkoittaa?
-
Mitä tuo +HSync -VSync tarkoittaa?
Vaakatason ja pystytason synkronointia.
Ja kun vielä toisessa on plussa-alku ja toisessa miinus-alku, niiden merkityksestä en sitten lähde sanomaan mitään, kun en ole varma.
-
Modeline "1680x1050" 146.00 1680 1784 1960 2240 1050 1053 1059 1089 +HSync -VSync
Modeline "1400x1050" 121.75 1400 1488 1632 1864 1050 1053 1057 1089
Tuossa ylemmässä rivissä on oikeat arvot, miksi en saa niitä toimimaan?
-
Täysin en voi verrata esim omaani, koska korttina minulla on nvidia, mutta kuitenkin.
Section "Modes"
Identifier "Modes[0]"
Modeline "1680x1050" 146.00 1680 1784 1960 2240 1050 1053 1059 1089 +HSync -VSync
Modeline "1400x1050" 121.75 1400 1488 1632 1864 1050 1053 1057 1089
EndSection
Tuo joka on sinulla, on minulla muotoa:
Section "Modes"
Identifier "Modes[0]"
EndSection
Jonka merkityksen vuoksi sanoinkin että en ole ihan varma.
Ja kysytääs, muilta, mitä muotoa teillä on tuo kyseinen kohta? Ati tai nvidian kortilla.
-
Ennen kun asensin atin ajureita niin toimi tolla suurimmalla resoluutiolla,
mutta asennuksen jälkeen ei? Google Earth kyllä alkoi pelittää.
Sax2 jos ottaa 3D kiihdytyksen käyttöön niin kaatu koko kone, eikä
auttanut kun uusi asennus, siis ennen atin ajurien asennusta.
-
Sax2 jos ottaa 3D kiihdytyksen käyttöön niin kaatu koko kone, eikä
auttanut kun uusi asennus, siis ennen atin ajurien asennusta.
Tai järkevämpi tapa, käynnistä kone ajotasolla 3, muokkaa sen jälkeen tuota xorg.conf tiedostoa ja kun olet muutokset tallentanut vaihda ajotaso 5:een.
UUdelleen asennusta ei yleensä tarvita.